----------------------------------- xtremefunny 10 Noi 2017 16:46 heq5 syntrek ----------------------------------- Am un HEQ 5 Syntrek Heavy-Duty are un hand controller foarte simplu doar pt RA si Dec. Are cineva o schema pt a conecta aceasta montura la calculator ?...Mentionez ca singura mufa este un RJ 11 cu 6 pini si cea de alimentare :). Multumesc mult ----------------------------------- nobody 11 Noi 2017 00:23 ----------------------------------- Vezi EQDIR: http://eq-mod.sourceforge.net/eqdirect2.htm ----------------------------------- xtremefunny 11 Noi 2017 15:16 ----------------------------------- Da, stiu schema asta, dar imi trebuie cu RJ 11 (6 pini) nu RJ 45 (8 pini) ----------------------------------- nobody 11 Noi 2017 18:32 ----------------------------------- Stai un pic. Esti sigur ca-i HEQ5 Syntrek ? Dupa poza arata a fi HEQ5 Classic. In cazul asta s-ar putea ca acel port cu 6 pini sa functioneze ca si autoguider. Ce vrei sa faci legand montura la calculator ? ----------------------------------- xtremefunny 12 Noi 2017 00:41 ----------------------------------- Da vreau sa l leg la calculator . Daca poate sa cineva stie pinout ul la RJ 11? Si ai dreptate cred ca e HEQ 5 Clasic cu controller ul din imagine. Daca vrei iti trimit mai multe poze. Daca ai vreo idee ar fi grozav ...Multumesc mult :) ----------------------------------- Mircea Pteancu 12 Noi 2017 01:10 ----------------------------------- Iti urez succes in rezolvarea problemei tehnice. Te rog insa sa scrii mesajele cat de cat corect. Sau ti le trimit la Spam.... sau in Catalonia. :shock: (Sper ca observi ca iti ofer alternative...) Mircea ----------------------------------- nobody 13 Noi 2017 15:44 ----------------------------------- Mai am voie sa-i raspund omului sau risc sa-mi ajunga mesajele prin ceva gulag siberian, ori ca alternativa, prin sudul Poloniei, pe undeva pe langa Auschwitz ? ----------------------------------- Mircea Pteancu 13 Noi 2017 23:22 ----------------------------------- Bitte , jawohl ! :twisted: von Mirkow ----------------------------------- xtremefunny 16 Noi 2017 14:32 ----------------------------------- Mai am voie sa-i raspund omului sau risc sa-mi ajunga mesajele prin ceva gulag siberian, ori ca alternativa, prin sudul Poloniei, pe undeva pe langa Auschwitz ? Chiar nimeni nu stie o metoda simpla de a lega un HEQ5 Classic la un calculator? ----------------------------------- valy 16 Noi 2017 15:02 ----------------------------------- Ce vrei sa faci legand montura la calculator ? Vrei autoguiding sau vrei gen goto? ----------------------------------- nobody 16 Noi 2017 17:44 ----------------------------------- Cea mai simpla metoda ar fi sa cumperi kit-ul original de upgrade la GOTO. Mai poti face un modul de genul: /* This file describes the data in the EQ6/Atlas hand paddle serial stream. * * This is a one-directional serial stream at 935 bits/sec. This is a fairly * wierd speed that seems to be used to give an overall serial stream time * of 76.2ms [basically the full-step time for siderial rate, which is * half of the actual half-step rate]. * * See the file eq6-serial.txt for further details. */ Pinout: Controller connector port: Pin numbers from RIGHT looking into socket with tab up (as numbered on controller board) 1: Switched +12V from hand controller 2: Ground 3: Data from hand controller via 1K resistor 4: Short to pin 1 5: +12V from source via diode 6: Short to pin 5 ----------------------------------- xtremefunny 17 Noi 2017 19:23 ----------------------------------- Cea mai simpla metoda ar fi sa cumperi kit-ul original de upgrade la GOTO. Mai poti face un modul de genul: /* This file describes the data in the EQ6/Atlas hand paddle serial stream. * * This is a one-directional serial stream at 935 bits/sec. This is a fairly * wierd speed that seems to be used to give an overall serial stream time * of 76.2ms [basically the full-step time for siderial rate, which is * half of the actual half-step rate]. * * See the file eq6-serial.txt for further details. */ Pinout: Controller connector port: Pin numbers from RIGHT looking into socket with tab up (as numbered on controller board) 1: Switched +12V from hand controller 2: Ground 3: Data from hand controller via 1K resistor 4: Short to pin 1 5: +12V from source via diode 6: Short to pin 5